making timbers visible in roof design module

Diese Seiten wurden speziell für die Benutzer unserer Software installiert, um sich untereinander und mit uns, Informationen, Neuigkeiten, Bilder und Dateien auszutauschen. Egal ob Dietrich's Abbundprogramm oder DC-Statik, hier sind alle Holzbau Profis richtig. Natürlich auch die ohne Holzbausoftware ;)


Wenn Sie selbst aktiv werden wollen, melden Sie sich unverbindlich mit einem Benutzernamen und einem Passwort an. Klicken Sie hierzu auf der linken Seite den Punkt "Benutzerkonto erstellen" an.


Wir wünschen unseren Besuchern einen informativen und angenehmen Aufenthalt bei Dietrich's FIX


Ihr Team Dietrich's Online - Holzbau ist unser Programm

1. offizieller Beitrag

    hello all,


    i have a roof timber (king post) that i made in the roof design module. since i needed to copy it a few times around i did so using d-cam.


    how can i make the copies visible in the roof design module? only the original shows.


    thanx,
    jorge

    i like building pianos

    • Offizieller Beitrag

    I think the copies belong to another builing MOS. Go back to d-cam and use function 6-4. Then select the building MOS to which you want to assign them and pick 'Elements: Add'. Now you select the posts.


    With this you should see them in roof design modul.

    Viele Grüße,
    Joachim Neumann (Dietrich's Technology GmbH)
    Software für den Holzbau, Abbund, Holzrahmenbau, Blockbau, Ingenieurholzbau und für die Fertighausindustrie

    thank you Joachim,


    i really apreciate the quick help. your solution worked, and i should have figured out that one myself.


    is it possible to make a corner post part of the two walls that meet at that corner, so i can see it as part of the bent, or as part of the section perpendicular to it when using the MOS. i think the MOS doesn't let me do it because that 's not its intended use. i have tried 6-4, and 6-6 (MOS-pakage/element) but they only let the piece be part of one package or the other, for obvious reasons.


    i know nothing about the intended use of 6-2 and 6-5 perhaps it is them i should be using?

    i like building pianos

    • Offizieller Beitrag
    Zitat von jorge

    .... is it possible to make a corner post part of the two walls that meet at that corner, ....


    No, it's not possible. Any part can belong only to one MOS 6-3 to 6-6. But it can belong to every free MOS (6-7), which you can only use with Dicam full version.


    6-2 works like a filter, but it does something more. In the last step it reads the actual MOS of the last chosen part.


    6-5 is like a "layer" MOS. You can use 6-4, 6-5 and 6-6 for your own purposes, 6-3 is normally used by the program.


    All parts, you enter in ceiling-, wall- or roof design, are automatically put into the correct building MOS.
    All parts, you create in Dicam, are put in the "actual MOS". You should always switch it to the "correct" one.

    • Offizieller Beitrag

    A volume can only belong to one single building MOS but you could assign the volume not to a wall but to the floor. So it does not belong to one of the both walls.
    I do not know why you need this. Normaly a volume belongs to one wall, one ceiling or one roof face. In wall construction you can switch on the volumes of other walls so you should see the post even if it belongs to another wall. To switch this on see 1-7-1, right upper corner.

    Viele Grüße,
    Joachim Neumann (Dietrich's Technology GmbH)
    Software für den Holzbau, Abbund, Holzrahmenbau, Blockbau, Ingenieurholzbau und für die Fertighausindustrie

Jetzt mitmachen!

Sie haben noch kein Benutzerkonto auf unserer Seite? Registrieren Sie sich kostenlos und nehmen Sie an unserer Community teil!

Benutzerkonto erstellen Anmelden